Cisco 1000 Series Fixed-Configuration
Desktop Access Routers

The Cisco 1000 series of compact, fixed-configuration routers are available in synchronous and asynchronous models.

There are currently three Cisco 1000 series models:

• Cisco 1003 ISDN router

  • One 10BaseT Ethernet port (RJ-45)

  • One ISDN BRI WAN port (RJ-45)

  • One console port (RJ-45)

  • One Type-2 PCMCIA slot for Flash ROM card

• Cisco 1004 ISDN router

  • One 10BaseT Ethernet port (RJ-45)

  • One ISDN BRI WAN port (RJ-45), with an integrated NT1 device

  • One console port (RJ-45)

  • One Type-2 PCMCIA slot for Flash ROM card

• Cisco 1005 serial router

  • One 10BaseT Ethernet port (RJ-45)

  • One serial WAN port (DB-60) that supports asynchronous serial communications up to 115.2 kbps (EIA/TIA-232 interface) and synchronous serial such as leased lines, Frame Relay, switched 56 kbps, SMDS, and X.25 up to 2.048 Mbps (EIA/TIA-232, EIA/TIA-449, V.35, X.21, and EIA-530)

  • One console port (RJ-45)

  • One Type-2 PCMCIA slot for Flash ROM card

The rear view of the routers looks the same except for the following differences, shown in the following figure:

• The BRI port on the Cisco 1003 is labeled "ISDN S/T," and "Cisco 1003" is stamped on the upper left corner of the chassis (not illustrated).

• The BRI port on the Cisco 1004 is labeled "ISDN U," and "Cisco 1004" is stamped on the upper left corner of the chassis (not illustrated).

The Cisco 1003 and Cisco 1004 routers include the following standard features:

• One Ethernet 10BaseT port with an RJ-45 connector

• One ISDN BRI port with an RJ-45 connector (the Cisco 1004 router includes an integrated NT1 device)

• One console port with an RJ-45 connector

• Console cable kit and power supply

• One external PCMCIA slot for optional Type-2 Flash memory card

• Software booting over an Ethernet LAN using TFTP

• Optional Flash memory card to store software image and configuration files, allowing network-independent booting and software updates over the WAN or LAN connections

• LAN-to-LAN DDR routing over ISDN lines

• IP, IPX and AppleTalk routing

• Transparent bridging

• IPX and SPX spoofing

• PPP compression and bandwidth-on-demand with load balancing for throughput up to 512 kbps

• HDLC and standards-based PPP

• Increased security with CHAP, PAP, packet filters, local password and CLI/ANI

• Network management and monitoring through the console port or over the network using SNMP or Telnet

• Support for Frame Relay

The Cisco 1005 router includes the following features:

• One Ethernet 10BaseT port (RJ-45)

• One console port (RJ-45)

• Console cable kit and power supply

• One serial port (DB-60) that supports:

  • Permanent and switched synchronous WAN links up to 2.048 Mbps

  • Asynchronous WAN links up to 115.2 kbps

• One slot for an optional PCMCIA Flash memory card

• Software boot using TFTP over an Ethernet LAN connection or by using the optional Flash memory card

• IP, IPX and AppleTalk routing

• Transparent bridging (over synchronous WAN links only)

• Support for the following synchronous WAN encapsulations: HDLC, LAPB, Frame Relay, SMDS and X.25

• Support for the following asynchronous WAN encapsulations: PPP and SLIP

• Router management through the console port or over the network using SNMP or Telnet

• AutoInstall for downloading configuration files automatically over a WAN

Technical Specifications for the Cisco 1000 Series

Description	Cisco 1003	Cisco 1004	Cisco 1005
Supported network interfaces	ISDN BRI (RJ-45 Ethernet 10BaseT (RJ-45) Console port (RJ-45) (EIA/TIA-232)	Same as Cisco 1003	Serial Port (DB-60) Ethernet 10BaseT (RJ-45) Console port (RJ-45) (EIA/TIA-232)
Processor	Motorola 69360	Same as Cisco 1003	Same as Cisco 1003

Part Numbers for the Cisco 1000 Series